An E-band Cassegrain switched beam high-gain antenna concept for 5G backhauling systems is proposed in this article. The antenna requirements target the compensation of small misalignments (within ±1 degrees in both azimuth and elevation planes) in E-band backhauling links due to adverse weather conditions or thermal deformations. The intended antenna is able to realize beam-switching operations by using a feed-array architecture based on a 7 × 7 array of cavity-backed magnetoelectric (ME) dipoles, where every element is capable of providing a steering of ±0.33 degrees in both the elevation and the azimuth planes. The ME dipole illuminators combined with a Cassegrain reflector provide a gain of 52 dBi within the whole scanning range. Besides, they can be easily integrable with the front-end modules, thus being an easily implementable and low-cost alternative to other more complex solutions based on horns or lens antennas.

Electronic measurement systems in the THz frequency range are often bulky and expensive devices. While some compact single-chip systems operating in the high millimeter-wave frequency range have recently been published, compact measurement systems in the low THz frequency range are still rare. The emergence of new silicon-germanium (SiGe) semiconductor technologies allow the integration of system components, like oscillators, frequency multipliers, frequency dividers, and antennas, operating in the low THz frequency range, into a compact monolithic microwave integrated circuits (MMIC), which contains most components to implement a low-cost and compact frequency-modulated continuous-wave-radar transceiver. This article presents a single transceiver solution containing all necessary components. It introduces a $0.48\,\mathrm{THz}$ radar transceiver MMIC with a tuning range of $43\,\mathrm{GHz}$ and an output power of up to $-9.4\,\mathrm{dBm}$ in the SG13G3 $130\,\mathrm{nm}$ SiGe technology by IHP. The MMIC is complemented by a dielectric lens antenna design consisting of polytetrafluoroethylene, providing up to $39.3\,\mathrm d\mathrm B\mathrm i$ of directivity and half-power beam widths of 0.95∘ in transmit and receive direction. The suppression of clutter from unwanted targets deviating from antenna boresight more than 6∘ is higher than $24.6\,\mathrm d \mathrm B$ in E- and H-Plane.

In this study, tunability of the electromagnetically induced transparency (EIT)-like transmission window by low-volume dielectric loadings is presented both numerically and experimentally in S-band. The EIT-like transmission behavior is obtained by a metamaterial, composed of an electric resonator and a closed-ring resonator patterned on a dielectric substrate. The frequency tuning is obtained by two applications called horizontal sliding application (HSA) and vertical sliding application based on sliding of the low-volume loadings from the edges to geometric center (i.e., inward). For both applications, the frequency tuning has been investigated for dielectric loadings which have relative permittivity of 2.2, 3, 4.5, and 6.15. The results reveal that the proposed sliding applications are effective on tuning the transmission peak frequency. An achieved 1136 and 971 MHz absolute spectral shifts and corresponding 6.34% and 5.41% absolute sensitivities by simulations and measurements, respectively, are the best results which are obtained for HSA at 5 mm shift value. Moreover, 14.67% sensitivity is obtained in simulations for the complete dielectric loading on the resonator in response to the increase in refractive index from 1 to 1.5. It is believed that the proposed applications will contribute to the existent sensing studies.

In this article, different 2D and 3D mask styles for synthesizing large array pattern shaping to meet the requirements of modern applications are realized. The composition of the different beam pattern shaping is achieved by comparing the array factor with the proposed masks whose details (upper and lower borders) are predefined according to the designer. The generated pattern shapes are as follows: unscanned 2D single-pencil beam, scanned 2D pencil beam, 2D multi-beam scanning, 2D wide flat beam with little ripple, unscanned 3D single-pencil beam, 3D multi-beam scanning, and footprint (or contour) pattern for linear and planar arrays. The process of constructing these patterns is followed by predicting the amplitude-only weights (i.e., the phase weighting is considered zero in all computations) of the elements using the particle swarm optimization algorithm. In all proposed masks, different sidelobe levels are controlled, ranging from −20 to −100 dB. Also, the radiated beamwidth is controlled, ranging from 0.1334 rad (7.6 deg.) to 0.4 rad (23 deg.). The analysis and construction of linear and planar array arrangements depend on the formulation of antenna array theory through the implementation of the proposed (estimated) equations using MATLAB code. The simulation results showed the effectiveness of the proposed methods in controlling the pattern shape according to the required modern trends.

An absorptive reconfigurable bandstop filter (BSF) with compact size and ultra-wide frequency tuning range using distributed lossy resonators is presented. In each reconfigurable bandstop resonator, a varactor and a PIN diode are utilized as the control and absorption devices. When the PIN diodes are in off and on states, the upper and lower frequency tuning ranges of stopbands can be obtained, respectively. Therefore, the ultra-wide total frequency tuning range which is the combination of the upper and lower frequency tuning ranges can be realized. Meanwhile, the stopband frequency and bandwidth tuning can be independently controlled by bias voltages. The resistances in the varactors and PIN diodes can dissipate the electromagnetic power and thus result in absorptive stopband without using extra absorptive circuits. The stopband suppression level and stopband absorption ratio are proportional to the number of distributed lossy resonators. For demonstration, an absorptive reconfigurable BSF prototype using six pairs of distributed lossy resonators is designed and fabricated. The measured total frequency tuning range is 3.03–6.39 GHz (71%) with the suppression level of 20 dB, while the frequency tuning range with the suppression level of 10 dB is 2.04–6.39 GHz (103%).

By combining the technique of energy selective surface and frequency selective rasorber, an energy selective rasorber is proposed, which performs selective energy protection in the low communication frequency band (0.8–2 GHz) and wave-absorbing property in the high-frequency band (6–18 GHz). The design consists of two layers, of which the bottom one contains a lumped diode structure for energy selection function in the transmission band, while together with the top layer, they perform a wideband wave absorbing function. The simulated and measured results agree well with each other, and both show good absorption in 6–18 GHz and energy-selective property around 1.86 GHz. That is, when the incident power changes from −30 to 14 dBm, the reflection coefficient changes from below −22 dB to above −2 dB, while the transmission coefficient changes from above −3 dB to below −17 dB.

With the rapid development of communication technology, the researches of multi-band filtering circuits have become more and more important. Multimode resonator (MMR) is one of the vital methods to provide multi-resonant modes within a single design. In this paper, a dual-band ultra-wideband bandpass filter (UWB-BPF) using stepped impedance stub-loaded resonators (SI-SLR) is presented. The main advantage of using SI-SLR is to have better performance with multimode behavior and more parameters to control resonant modes. SI-SLR combines the advantages of SIR and SLR structures, which gives a compact, high-performance multiband filter. The proposed filter design has compact size, sharp and flat response with low insertion loss (IL), low return loss (RL), and high band-to-band rejection. The filter is designed for UWB communication in wireless body area networks and fabricated on Arlon substrate with relative permittivity ${\varepsilon_{\textrm{r}}} = 3.25$, thickness $0.8\;{\textrm{mm}}$. The resulted dual-bands are centered at $4{\textrm{ GHz}}$ and $8.3{\textrm{ GHz}}$ with fractional bandwidths $37{\textrm{% }}$ and $48{\textrm{%}}$. The simulation was carried out using CST Microwave Studio. The filter provides good passband performances, with IL 0.49 dB and 0.31 dB at the center frequency of lower and higher bands, respectively. The band-to-band 40 dB rejection is realized by adding circular spiral at the input/output of the filter.

A novel thinned antenna element distribution for cancelling grating lobes (GLs) as well as for reducing phase shifters (PSs) is presented for a two-dimensional phased-array automotive radar application. First, an efficient clustering technique of vertical adjacent elements is employed with array thinning for a PS reduction of 66.7%. In the proposed distribution, several single-element radiators (non-clustered antenna elements) are placed in the vertical direction with specific spacing in a grid of 16 × 12 (192) elements with λ/2 pitch. This disrupts the periodicity of phase-centers after element-clustering and takes a role as steerable GL canceller with capabilities of tracking and nullifying the GL at any scan angle. The proposed distribution enables beam steering up to ±60° in the azimuth plane, as well as ±25° in the elevation plane with cancelled GL and sidelobes. Furthermore, the proposed distribution has been efficiently calibrated with all elements activated by introducing the code division multiple access technique. To the best of the authors’ knowledge, this work represents the first fully calibrated state-of-the-art thinned distribution phased-array including a novel steerable GL canceller to track and nullify GLs.

A wideband antipodal Vivaldi antenna has been designed and optimized. A slight improvement is obtained by employing multiple metalense based on circular split-ring resonators to maximize the antenna gain with the maximum bandwidth. The designed antennas have been fabricated and characterized, showing good agreement with simulations. The maximum measured gain is $G = 12\;{\textrm{dB}}$, and the −10 dB bandwidth is from $f = 3\;{\textrm{GHz}}$ to $f = 13\;{\textrm{GHz}}$.

This paper presents the application of a substrate-integrated waveguide (SIW) for the design of a leaky-wave antenna (LWA). The antenna radiates through a wide slot in the top wall of the SIW structure in the forward direction. The effective width of the slot is varied by changing capacitances of two arrays of varactors connected between slot edges and inserted conducting strips. The radiation pattern of the antenna is by this way controlled by DC bias, which sets the capacitances of varactors. The maximum radiation direction in elevation can be varied within 35° by changing the DC bias from 2 to 12 V. This elevation angle is measured from the broad side direction perpendicular to the antenna substrate. The measured antenna characteristics are in accord with those predicted by simulation. The antenna can be simply fabricated by a planar circuit board technology.

In [A. Capozzoli, C. Curcio, A. Liseno, MMS, Pizzo Calabro, Italy, 2022], the problem of modeling a source/scatterer using an equivalent radiator has been addressed and an approach has been given and numerically assessed.

Once dimensioned the radiating panel, a practical implementation can be provided by a non-uniform array. The element positions should be chosen so that the array is capable to approximate, with an adequate accuracy, the fields radiated by the equivalent radiator. Here, the array element positioning is performed by exploiting a quadrature rule which takes into account that the singular functions supported on the region of interest associated to the most significant singular values of the radiation operator are related to those supported on the equivalent panel by a radiation integral. The quadrature rule enables also to choose a set of weights which are essential in the definition of the element excitation coefficients from the knowledge of the source distribution on the equivalent panel. For simplicity, a one-dimensional problem with a Legendre quadrature rule is considered. The approach is numerically assessed by checking the capability of the array to radiate, with a satisfactory degree of accuracy, the singular functions associated to the region of interest.

A low-profile wideband circularly polarized (CP) metasurface antenna is demonstrated for C-band applications. The metasurface consists of 4 × 4 square patches with Z-shaped slots. Characteristic mode analysis is used to investigate the modal behavior of the metasurface, and a pair of degenerate modes is chosen as the operating modes. The CP radiation is realized by exciting a pair of degenerate modes of the metasurface through a slot antenna, which is used as a feed structure with a 90° phase difference. The CP bandwidth is further widened by combining the resonance modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the antenna is 3.47–4.76 GHz, and the 3 dB axial ratio bandwidth is 3.5–4.9 GHz with a peak gain of 6.9 dBic. Moreover, the antenna exhibits well left-hand CP radiation performances with a low profile of 0.046λ0.

This paper presents an integrated power amplifier (PA) following the orthogonal load-modulated balanced amplifier (OLMBA) topology. The fixed-phase prototype in this paper is implemented with 22 nm complementary metal oxide semiconductor (CMOS) fully depleted silicon-on-insulator (FDSOI) process. The proposed PA operates at 26 GHz frequency range, where it achieves 19.5 dBm output power, 16.6 dB gain, 15.7% power added efficiency, and 18.3 dBm output 1-dB compression point ($P_{\rm 1\,dB}$). The PA is also tested with high dynamic range modulated signals, and it achieves, respectively, 11.4 dBm and 4.9 dBm average output power (Pavg) with 100 MHz and 400 MHz 64-QAM third-generation partnership project/new radio frequency range 2 signals, and 14 dBm Pavg with 0.6 Gb/s (120 MHz) single carrier 64-QAM signal, measured at 26 GHz and using −28 dBc adjacent channel leakage ratio and −21.9 dB (8%) error vector magnitude as threshold values. The proposed OLMBA is also compared to a stand-alone quadrature-balanced PA. Modulated measurements show that the stand-alone quadrature-balanced PA has better linearity in deep back-off, but the OLMBA has better efficiency.

This paper proposes a design method for designing a wideband filtering power amplifier (PA) based on terminated coupled line structure (TCLS). This method generates four transmission zeros and three transmission poles by loading stepped impedance resonator and short-circuit stubs on the four ports of TCLS, which greatly optimizes the in-band return loss and stopband suppression of the output matching network. In addition, the effective suppression of the second harmonic also increases the efficiency of the PA. In order to verify the effectiveness and superiority of this design method, a wideband bandpass filtering PA is designed and manufactured in 2.9–3.7 GHz. Measurement results show that the saturated output power is from 40.1 dBm to 41.2 dBm, the drain efficiency is greater than 60.3%, and the gain is 10–11.2 dB.

This research article represents the design of a simple, smaller, and novel frequency reconfigurable patch antenna for 5G communication using PIN diodes. This antenna operates in both mid-5G and high-5G bands. The antenna is intended to operate in eight distinct modes with three PIN diodes in 5G wireless communication covering 27.46–50 GHz of high-5G band (range n257/n258/n260/n261/n262) and frequencies of the 3–6 GHz of mid-5G band (range n77/n78/n79/n46). The antenna has an overall size of 20 mm × 25 mm × 1.6 mm and is placed upon a low-cost FR4 substrate. A higher radiation efficiency from 75% to 98% is achieved in all the different modes. The resonant frequencies are around 3.46, 4.43, 5.83, 31.8, 35.5, and 46 GHz in different modes of operation. Different switching statuses have been carried out in this research work and their performances have also been illustrated in the form of surface current distribution in different resonant frequencies. The simulated and measured results are compared to highlight its proposed design operation.

This paper proposes a wideband four-element multiple-input multiple-output (MIMO) antenna operating in the millimeter-wave frequency band for 5G communications from 24.37–39.44 and 45.09–50.62 GHz. The antenna design has been realized using Rogers 5880 substrate and consists of a T-shaped strip that is attached to the top of a 50 Ω feeding line. Two microstrip lines are affixed at the terminal points of T-shaped strip and bent toward the feeding structure. These bent strip lines are then extended by joining two additional L-shaped microstrip lines. On the back, there is a partial defective ground plane featuring a rectangular slot and a thin strip line located at its center. The dimensions of the proposed single element and MIMO antenna are 0.933λ × 0.933λ × 0.024λ and 1.865λ × 1.865λ × 0.024λ, respectively (at 28 GHz), while the edge-to-edge distance between the radiation elements of the MIMO antenna is 4.0 mm. The design incorporates an efficient passive fan-shaped decoupling structure to decrease coupling between antenna elements. Simulations and experimental results show good agreement with each other. For all resonant frequencies the measured peak gain is greater than 4.85 dBi, radiation efficiency is over 90%, diversity gain is greater than 9.5, ECC is less than 0.025, TARC is less than -10 dB and CCL is below 0.4 bits/s/Hz. The proposed MIMO antenna, with its wide bandwidth, high gain, high inter-port isolation, and high efficiency characteristics, can be used for 5G wireless communication applications.

A system-in-package for a wideband digital radar, in D-band, requires broadband, high-gain antennas combined with broadband chip-to-package and package-to-printed circuit board (PCB) interconnects. This paper demonstrates a wideband, low-loss quasi-coaxial signal transition, and a novel electric split ring resonator (eSRR)-based antenna-in-package (AiP) with a modified reflector concept, for improved gain, in embedded wafer level ball grid array (eWLB) technology. A complete chip-to-package-to-PCB interconnect is also demonstrated by combining the quasi-coaxial transition with a chip-to-package interconnect. The quasi-coaxial signal transition has the largest impedance bandwidth among ball grid array-based quasi-coaxial signal transitions. For the modified reflector concept, a horn-shaped cavity is micromachined in the PCB substrate and remetallized with aerosol-jet printing, placing the reflector 0.25λ from the antenna. The antenna gain is improved with up to 5.3 dB. The AiP with the horn-shaped reflector is the single element with the highest gain, in eWLB technology, above 100 GHz.

This paper proposes fractal-inspired array antennae for wideband applications. The proposed antennae have a resonance frequency range of 20–40 GHz. The modified fractal antennae are fabricated with a height of 1.6 mm, substrate width, and length of 100, 50, 25, and 18.75 mm2, and a simulated result shows that the gain is increased to 11.04, 11.9, 8.4, and 6 dBi, and the designed antennae radiate power with directivity of 11.3, 13.4, 9.29, and 7.17 dBi concerning proposed designs A, B, C, and D, respectively. The proposed antennae with 5G New Radio (NR) bands have more radiation concerning resonate frequencies in the 20–40 GHz range with Φ = 0°, Φ = 90°, and θ = 90°. Moreover, the bandwidths for applications covered in the 5G NR and sub-6G are 1.92, 0.73, 0.7, 2.4, 1.3, 5.3, and 1.26 GHz, and 3.4, 3.7, 2.67, and 4.65 GHz, and 2, 3.5, and 1.57 GHz, and 2.5, 1.5, and 1.0 GHz with the maximum return loss of 37 dB, 32.8 dB, 31.2 dB, and 23 dB with corresponding resonate frequencies as 21.5, 27.6, 33, and 27.6 GHz concerning designs A, B, C, and D, respectively. The proposed antennae have been implemented and validated using Computer Simulation Technology (CST), Vector Network Analyzer (VNA), spectrum analyzer, and power sensor.

In this paper, the development and designing of angle-independent metamaterial microwave absorbers are presented. The unit cell consists of two concentric circle that are linked by consolidated resistors. The absorber is built on a dielectric substrate (FR4) with a thickness of 3.2 mm (λ/0.07) and a dielectric constant of 4.3. The wideband absorption is acquired in the range of 2.8 to 10.42 GHz with a wide band of 7.62 GHz with absorptivity above 90%. In the area of interest, a flat band is obtained, and to examine the current distribution and electric field in the respective region, two peaks are considered at a frequency of 3.66 and 9.54 GHz, with maximum absorptivity of 99.99% and 99.44%, respectively. The presented absorber is examined under different angles for phi and theta variation. From the phi variation, it is observed that for all the angles, absorptivity does not vary, which confirms that the absorber is acting as an angle independent. The fabricated sheet consists of an array of a unit cell, which is examined inside the anechoic chamber with the help of two horn antennas and vector network analyzer. The tested and simulated results are compared, and it was observed that they are close in their agreement. At the end of the manuscript, the presented and already reported arts are compared, and it is observed that the presented one operates for the low frequency with higher bandwidth. The presented absorber can be practically used for defense applications for Radar Cross Sections reduction.

The design and development of a microstrip-based planar ultra-wideband (UWB) bandpass filter (BPF) with single/multiple interference rejection capability is presented. The proposed BPF structure is developed based on the broadside coupled mechanism of microstrip/coplanar waveguide (CPW). The BPF has microstrips and short-circuited CPW capacitively coupled through the substrate. The basic frequency response generated from this geometry covers the necessary UWB spectrum (3.1–10.6 GHz) and possesses appreciable characteristics due to dual transmission zeros at either passband boundary. Multiple resonators are embedded in the basic BPF structure to develop passband notches to circumvent unnecessary interferences. A low-pass filter is later integrated into geometry to extend the upper stopband. The proposed structure is compact and covers an area of only 14 × 11.4 mm2.