Hostname: page-component-54dcc4c588-42vt5 Total loading time: 0 Render date: 2025-09-11T07:05:30.449Z Has data issue: false hasContentIssue false
  • English
  • Français

On the drag-out problem in liquid film theory

Published online by Cambridge University Press:  25 December 2008

E. S. BENILOV  and
V. S. ZUBKOV
E. S. BENILOV*
Affiliation:
Department of Mathematics, University of Limerick, Ireland
V. S. ZUBKOV
Affiliation:
Department of Mathematics, University of Limerick, Ireland
*
†Email address for correspondence: eugene.benilov@ul.ie
Get access Rights & Permissions [Opens in a new window]

Abstract

We consider an infinite plate being withdrawn (at an angle α to the horizontal, with a constant velocity U) from an infinite pool of viscous liquid. Assuming that the effects of inertia and surface tension are weak, Derjaguin (C. R. Dokl. Acad. Sci. URSS, vol. 39, 1943, p. 13.) conjectured that the ‘load’ l, i.e. the thickness of the liquid film clinging to the plate, is l=(μU/ρgsinα)1/2, where ρ and μ are the liquid's density and viscosity, and g is the acceleration due to gravity.

In the present work, the above formula is derived from the Stokes equations in the limit of small slopes of the plate (without this assumption, the formula is invalid). It is shown that the problem has infinitely many steady solutions, all of which are stable – but only one of these corresponds to Derjaguin's formula. This particular steady solution can only be singled out by matching it to a self-similar solution describing the non-steady part of the film between the pool and the film's ‘tip’.

Even though the near-pool region where the steady state has been established expands with time, the upper, non-steady part of the film (with its thickness decreasing towards the tip) expands faster and, thus, occupies a larger portion of the plate. As a result, the mean thickness of the film is 1.5 times smaller than the load.

Information

Type
Papers
Information
Journal of Fluid Mechanics , Volume 617 , 25 December 2008 , pp. 283 - 299
Copyright
Copyright © Cambridge University Press 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

REFERENCES

Bertozzi, A. L. & Brenner, M. P. 1997 Linear stability and transient growth in driven contact lines. Phys. Fluids 9, 530–539.CrossRefGoogle Scholar
Derjaguin, B. 1943 Thickness of liquid layer adhering to walls of vessels on their emptying and the theory of photo- and motion-picture film coating. C. R. (Dokl.) Acad. Sci. URSS 39, 13–16.Google Scholar
Derjaguin, B. 1945 On the thickness of the liquid film adhering to the walls of a vessel after emptying. Acta Physicochim. URSS 20, 349–352.Google Scholar
Derjaguin, B. V. & Titievskaya, A. S. 1945 An experimental study of the thickness of a liquid layer left on a rigid wall by a retreating meniscus. Dokl. Acad. Nauk SSSR 50, 30–34.Google Scholar
Dussan, V. E. B. 1979 On the spreading of liquids on solid surfaces: static and dynamic contact lines. Annu. Rev. Fluid Mech. 11, 371–400.CrossRefGoogle Scholar
Jin, B., Acrivos, A. & Münch, A. 2005 The drag-out problem in film coating. Phys. Fluids 17, 103603.CrossRefGoogle Scholar
Kalliadasis, S., Bielarz, C. & Homsy, G. M. 2000 Steady free-surface thin film flows over topography. Phys. Fluids 12, 1889–1898.CrossRefGoogle Scholar
Landau, L. & Levich, B. 1942 Dragging of liquid by a plate. Acta Physiochim. USSR 17, 42–54.Google Scholar
Moriarty, J. A., Schwartz, L. W. & Tuck, E. O. 1991 Unsteady spreading of thin liquid films with small surface tension. Phys. Fluids A 3, 733–742.CrossRefGoogle Scholar
Shikhmurzaev, Y. D. 2006 Singularities at the moving contact line. Mathematical, physical and computational aspects. Physica D 217, 121–133.Google Scholar
Wilson, S. D. R. 1982 The drag-out problem in film coating theory. J. Engng Maths 16, 209–221.CrossRefGoogle Scholar